According to Apple, enabling Trim using the trimforce. Will give 10.10, 10.11, and 10.12(again) a try, and if I can force the 10.14 install, 10.14 too. 4, the trimforce command is available in Terminal to enable Trim without the use of third-party software. This question is regarding a mid-2010 MacBook Pro running macOS High Sierra. To enable TRIM, first save all your open documents as this will reboot your Mac. A slightly slower initial reboot, which apparently is from some kextcache and bootcache updating, but no issues. But, it doesn't specify per drive anywhere. sleep / wake is an issue, rest everything works fine. Imaged over a working 10.13.6 system applied the "sudo trimforce enable" and letting it reboot, resulted in no problems. Hello All, I am writing this from my first build. Nothing worked for the 10.12 "sudo trimforce enable" try. I can do a clean install, but also kinda curious about this.ĮDIT: Updating, since this is all experimentation for me. Assuming that the computer needed time to do stuff, I let it run, but it's not moving. Apple Logo shows, progress indicator stops at about 90%. Trying to do the same for the 10.12 partition has made that system not boot. Enabling it under 10.6.8 gave no problems (Trim Enabler 2.2) on that partition. Playing with an old computer that has never had TRIM enabled. View attachment 554217 SetApfsTrimTimeout & ThirdPartyDrives options.Enabling TRIM on an SSD that has never had TRIM enabled for 10 years. I want to do whichever is best, this kext patch, or the trim force command. View attachment 554215 View attachment 554216 Is this better than using trimforce I just did a clean install of 10.13.2 and my new nvme drive has trim enabled by default, but my SATA SSDs (previous 10.12.6 OS drive, and a windows 10 drive) now show trim is not enabled, though it was under 10.12.6. but it's only is an issue if the drive is. (he later wrote) A little late with this link, a review of the Intel 335, its sandforce controller and trim. View attachment 554214 Select Enable Trim from drop down menu in Clover Configurator But in a 2011 OWC blog post they didn't recommend using a Trim enabler on them.) Crucial or other brands not using a Sandforce controller seem to work fine with trim enabled. ![]() By the way, TRIM should be enabled by default for NVMe. ![]() This of course assumes you are not running macOS Monterey, as the trim command stopped working in Monterey. Since the TrimEnabler official page says TrimEnabler 4 is supported. Open a terminal (Finder > Go > Utilities > Terminal) and enter the following command: sudo trimforce -enable. So it is only run as and when you choose to change the setting. You can of course change the SetApfsTrimTimeout entry from say '4294967295' back to '-1', once you are sure the Trim command has been completed on your SSD. Have a careful read of the information above and see what you make of it. Setting a timeout figure in the SetApfsTrimTimeout entry will give OC more chance of fully completing the Trim command, this may make the boot time longer, depending on when you last ran the Trim command on your SSD. SetApfsTrimTimeout & ThirdPartyDrives options.Įnabling the ThirdPartyDrives option in your ist should enable the Trim option. The screenshot below contains the information provided by the OpenCore developers in their OC Configuration guide, which starts on page 35 in the Configuration.pdf for OC 0.8.3. Trim Enabler 4 is rewritten from scratch with a brand new UI and improved features, allowing you to enable Trim safely on current and upcoming versions of macOS. In OpenCore the process can be a little more complicated, in that you may need to set a time for the trim action to work, this can effect the time it takes to boot your system from a cold start. At the prompt, type sudo trimforce enable Press enter. Remember to unselect the Disable patch option, which is automatically enabled when this patch is selected in Clover Configurator. Find Enable TRIM for Any SSD in OS X 10.10.4 or Later GA S REGULAR Menu Lifewire Tech for Humans. Select Enable Trim from drop down menu in Clover Configurator Microsoft Windows, 200910Windows 7 and Windows Server. ![]() When using Clover you can add the following patch to the Kext and Kernel Patches section of your ist to enable trim. 4, Apple added a command line utility, trimforce, that can be used to enable TRIM on third-party SSDs. Building a CustoMac Hackintosh: Buyer's GuideĪre you using Clover or OpenCore as your bootloader?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |